Click me
Transcript

Netgear Extender Setup using installation Assistant

NETGEAR EXTENDER SETUP - THE WHOLE PROCESS A WIFI Extender is a device that can do wonders for you, provided you have the understandings of how to set it up properly. When it comes to extenders, Netgear tops the charts with its amazing fleet of extenders. However, their efficiency and performance totally depend upon how you set them up, so the main focus today will be on Netgear Extender Setup. Therefore, if you have unpacked the extender and now looking for a perfect place where you can rest the extender, then this is something you should do later on. The most important thing that you need to ensure is keeping the extender in the same room where your router is. There are two ways of setting up WiFi Range Extender, using Netgear Installation Assistant and WPS method.Let's find out both methods in detail. Netgear Extender Setup using installation Assistant: 1 • Connect the extender to a power source. • Make a connection with your Wi-Fi enabled device is created, the client link LED lights. • Wait for the power LED to turn green. • On your computer, launch a web browser. • Once it does, you will have to connect the device using wired Ethernet or Wi-Fi connection. • Type in 'www.mywifiext.net' or 'http://192.168.1.250 in the address bar. • Connect an Ethernet cable to an Ethernet port on the extender with its other end going to the • As the webpage opens, find and click the 'New Extender Setup' button. computer. • Enter details in the empty fields and click the 'Next' • To connect with Wi-Fi on your smartphone or tablet, open the WiFi connection manager and find your extender network on the list. button. 3 4 • You need to verify the 'Access Point/Extender' • Connect your WiFi-enabled devices such as your smartphone, tablet, laptop, and others to the WiFi network established by your extender using the SSID and password, which you create a few steps switch, whether it is set to the extender. If it is, then click the 'Continue' button. • Select the router's WiFi network that you wish to extend and then, click the 'Next button. earlier. • Make sure that the WiFi-enabled device is successfully connected before clicking the 'Continue' • In the 'Password' field, enter the router's password and click the 'Next' button. button. • Set the network name (SSID) and password for the • Click the 'Continue' button and then, click 'Next'. extender and click the 'Next' button. 5 6. • Complete the registration fields and then, click 'Finish' to complete the setup. • If the router link LED is not glowing green or amber light, then you will have to bring the extender further close to the router. • Now, you can unplug the extender and move it to a new location, which is about halfway between the router and the area where you were not getting any internet signals. • Reconnect the computer or WiFi device to a new extended WiFi network. • Plug the extender into an electrical outlet and wait until the power LED goes green. • Now, test the extended WiFi range by moving your computer or WiFi device to an area with a poor router WiFi signal. • Use the router link LED to guide you with the right spot where the extender to router connection is optimal. With that, your extender setup process is complete and now, you shall use the internet signals in rooms where internet signals used to remain absent. Visit Us : https://mywifiextfix.com/ Call Us : +1 888 905 2331

Netgear Extender Setup using installation Assistant

shared by mywifiextfix on Jun 02
23 views
0 shares
0 comments
If you recently purchased a Netgear extender and looking for some tips on how to setup Netgear extender, then you are at right place. Here you will get step to step instructions on Netgear Extender Se...

Tags

None.

Source

Unknown. Add a source

Category

Technology
Did you work on this visual? Claim credit!

Get a Quote

Embed Code

For hosted site:

Click the code to copy

For wordpress.com:

Click the code to copy
Customize size